Free Septic System Size & Cost Calculator
Find the septic tank size, drainfield area and installed cost for your home in seconds — from real onsite-wastewater design rules, with a transparent line-by-line breakdown.
Soil accepts effluent well and the water table is deep, so a conventional gravity drainfield is the simplest, lowest-cost option.
| Soil / percolation test | $300 |
| Design & permit | $600 |
| Septic tank (1,000 gal, supplied & set) | $1,200 |
| Conventional gravity gravel trench (645 ft²) | $3,250 |
| Excavation & site work | $1,200 |
Planning estimate from standard onsite-wastewater design rules, calibrated to 2026 contractor ranges. Most codes also require a 100% reserve area (~645ft²). Your county health department's approved soil test and design govern the final permit.
What each system would cost for these inputs. Greyed rows aren't suitable for your soil or water table.
| System | Dispersal area | Installed cost |
|---|---|---|
| Conventional gravityRecommended | 645 ft² | $3,950–$8,500 |
| Chamber | 385 ft² | $3,600–$7,800 |
| Mound | 565 ft² | $9,100–$19,700 |
| Aerobic (ATU) | 750 ft² | $9,500–$20,550 |
A detailed, shareable PDF for this exact estimate: tank & drainfield sizing with reserve area, all four system options costed, your state's permit checklist, soil/perc guidance and the questions to ask installers. Built for your inputs above.
How septic sizing actually works
Two numbers decide almost everything about a septic system: how much wastewater the home produces, and how fast the soil can absorb it. Codes estimate the first from the number of bedrooms — usually about 150 gallons per bedroom per day — and the second from a percolation test that measures how many minutes it takes water to drop an inch in your soil.
From there the math is straightforward and the same everywhere: the tank is sized to hold at least two days of flow (with code minimums by bedroom count), and the drainfieldis sized so the soil can absorb a full day's flow without surfacing. When the soil is too slow or the water table too high, a conventional field won't pass and you step up to a mound or aerobic system. The calculator above runs exactly this logic and shows every number, so nothing is a black box.
Frequently asked questions
- What size septic tank do I need?
- Septic tanks are sized by the number of bedrooms (a proxy for daily wastewater flow) with a minimum of two days' working capacity. A 1–3 bedroom home almost always needs a 1,000-gallon tank, a 4-bedroom home about 1,250 gallons, and a 5-bedroom home about 1,500 gallons. A garbage disposal usually bumps you up one size.
- How is the drainfield size calculated?
- The drainfield (leach field) area equals your design daily flow divided by the soil's long-term acceptance rate — the gallons each square foot can absorb per day. Fast soils like sand absorb a lot (small field); slow clay soils absorb little (large field). A percolation test gives the rate that sets this number.
- How much does a new septic system cost?
- A conventional gravity system on good soil typically runs $4,000–$9,000 installed. Mound and aerobic (ATU) systems for poor soils, high water tables or small lots commonly run $10,000–$20,000. The calculator above breaks the estimate into transparent line items and scales it to your state.
- How often should a septic tank be pumped?
- As a rule of thumb, plan to pump roughly once per 1,000 gallons of tank capacity, adjusted for household size. A 1,000-gallon tank serving a family of four typically needs pumping every 2–4 years; a 1,500-gallon tank every 3–5 years. The calculator estimates your interval from tank size and occupancy.
- Is this a permit-ready septic design?
- No — this is a fast, transparent planning estimate built from standard design rules. A permit requires a soil/percolation test and a design accepted by your county health department. SepticCalc Pro produces a detailed design-estimate report to take to a designer or installer.